Key takeaways
- A used Bobcat skid steer is worth buying when hours, hydraulic flow, and undercarriage wear check out against the model year's known issues.
- Price against comparable active listings on MachineryTrader and EquipmentTrader, staying within about 10% of the middle of the pack.
- Above roughly 5,000 hours, price mostly reflects remaining undercarriage and hydraulics life rather than the machine itself.
- A skid steer mulcher needs high-flow hydraulics, typically 30+ GPM, plus a larger frame class with strong cooling to run without stalling or overheating.
- Verify the PIN plate against the title, run a lien search in the seller's state, and get any warranty terms named in writing before money moves.
A bobcat skid steer for sale used is worth buying when hours, hydraulic flow, and undercarriage wear check out against the model year's known issues, and it's worth pricing off comparable active listings rather than asking prices. This guide covers inspection and pricing by model year, Bobcat vs John Deere, mulcher fitment, and how to list it so it moves.
What should I inspect before buying a used Bobcat skid steer?
Lift arms, tilt cylinders, and bushings
Start with the machine unloaded and on the ground. Raise the lift arms fully and watch both sides settle: if one arm drifts down while the other holds, you are looking at a cylinder seal or a load-holding valve problem, not a minor leak. Grab each tilt cylinder rod and check for scoring, then run a pry bar against the bucket to expose play in the pivot pins. Bushings are cheap; a cracked lift arm weld is not. Match what the seller claims against the official numbers for that model, including rated operating capacity and hydraulic flow, on Bobcat's own spec sheets, because a tired S175 will not move what a fresh one did.
Undercarriage and tires vs tracks
On wheeled units, check tire tread depth across the width; uneven wear points to a bent axle or bad bearings. On tracks, look for worn sprockets, loose chains, and cracked lugs. Track replacement runs into four figures, so price it before you bid.
Hydraulic system and quick-attach coupler
Warm the machine, then cycle every function and watch for foamy oil or slow response. Check the reservoir for milky fluid, a sign of water. Work the quick-attach lever with the bucket raised: the coupler should lock and release cleanly.
Cab, controls, and hour-meter sanity check
Compare hours to wear. A unit showing 1,500 hours with a shredded seat, worn joystick boots, and polished foot pedals has lived hard. If the hour meter reads low but the undercarriage and pedals say otherwise, walk. For a fuller machine-class comparison, see compact wheel loader vs skid steer.
How much should a used Bobcat skid steer cost by model year and hours?
Price bands by model era (illustrative)
These bands are illustrative, not quotes. Older 700/800-series machines from the 1990s and early 2000s typically trade in the $8,000–$15,000 range depending on condition. Mid-2000s to early-2010s S-series and A-series units often sit between $15,000 and $30,000. Newer S-series and R-series machines with low hours can run well past $40,000. Check what comparable units actually list for before you commit.
How hours move the price
Hours matter as much as year. A 2015 unit at 4,500 hours with a worn undercarriage can price below a 2010 unit at 1,800 hours. Ask for service records and check whether hour-meter readings match wear on the pedals, seat, and bucket edge. Above roughly 5,000 hours, price mostly reflects remaining undercarriage and hydraulics life.
Pricing against live listings
Pull active listings on MachineryTrader and EquipmentTrader, sort by model and hours, and price within 10% of the middle of the pack. On BigEquipCo, featured listings get priority placement in the dealer directory, so a sharp price plus a featured listing moves inventory faster. The same discipline applies across categories: a wheel loader priced against live comps sells the same way (see wheel loaders for sale).
Used Bobcat vs used John Deere skid steer: which holds up better for my jobs?
Parts and dealer network
Bobcat has the deeper parts shelf for used units. Skid steers, couplers, and buckets turn up at salvage yards and dealer counters everywhere, which matters when a buyer calls you about a down machine. John Deere parts are equally solid but often routed through the ag dealer network, so wait times can stretch in equipment-heavy regions. Check John Deere's official skid steer spec pages against Bobcat's when quoting specs to a buyer.
Resale and listing velocity
On our dealer directory, yellow iron moves, but used Bobcats consistently clear faster than comparably speced Deere units because private buyers recognize the name. Deere units sit longer but often fetch more from municipal and ag buyers. Price accordingly and expect a longer listing window on the Deere.
Job-fit differences
Bobcat's radial-lift models dig better; Deere's vertical-lift units carry pallets higher. Neither is "better" — match lift path to the buyer's work. We cover the lift-path tradeoffs in our skid steer vs compact track loader guide.
When does a mini skid steer Bobcat make more sense than a full-size used unit?
Access, weight, and trailer limits
A mini skid steer Bobcat wins when the job site, not the work, is the constraint. If you are running through 36-inch gates, inside batch plants, or across finished landscaping where a full-size machine leaves ruts, the smaller footprint pays for itself. Weight matters too: many mini units tow behind a pickup with a single-axle trailer, while a full-size skid steer plus trailer can push you past common tow ratings. If your truck is already committed to hauling a dump truck load of tools or a telehandler is booked elsewhere, the mini keeps a crew moving.
Cost and attachment overlap
A used mini costs less up front and burns less fuel, but check your attachments first. Buckets and forks often cross over; a skid steer mulcher usually does not. If you already own full-size attachments, the overlap may not justify a second set. Browse what is available on BigEquipCo's dealer directory before you commit, and list any machine you are trading toward on the same site.
Can I run a mulcher on a used skid steer, and what specs matter?
Yes, but only if the machine's hydraulics match the mulcher head. Most drum mulchers need high flow to cut cleanly, and a used Bobcat that was spec'd for buckets and augers often falls short.
Hydraulic flow and pressure requirements
Check the flow rating on the data plate before anything else. Standard-flow machines (roughly 17-23 GPM on Bobcat's published specs) run lighter heads slowly; high-flow setups (30+ GPM) are what most rotary and drum mulcher heads expect. A mismatch means stalling in dense brush and glazing the hydraulic oil.
Machine class and cooling
Mulching is a sustained-load job, so engine horsepower and cooling capacity matter as much as flow. A 75+ hp machine in the larger frame class holds RPM under load; a smaller unit overheats. Also inspect the auxiliary hydraulic circuit for prior mulcher use, since seals and quick couplers wear fast on these jobs.
Buying a skid steer mulcher used
Used mulcher heads sell at auction alongside machines, and sold-price data from Ritchie Bros. auctions gives a realistic band before you bid. Budget for new cutting teeth either way. If a high-flow mulcher unit isn't in your yard, cross-shop what you do carry; our dealer inventory spans other iron too, like motor graders.
Where is the safest place to buy a used Bobcat skid steer online?
Marketplaces vs auctions vs classifieds
Marketplaces like MachineryTrader and EquipmentTrader list dealer inventory with hours and specs up front, so you can screen units before calling. Auctions through IronPlanet and Ritchie Bros. Auctioneers move fast but give you limited inspection time. Classifieds like Craigslist and Facebook Marketplace are free and local, as dealers on Heavy Equipment Forums report, but you inherit more of the verification work yourself. Each channel also changes what you can verify before money moves: on a marketplace you can request undercarriage photos and service records while the unit is still listed, which mirrors the inspection sequence you would run in person. At an auction the preview window is often a single day and the hammer price is final, while on classifieds the seller may be a first-time lister with no service history, so the PIN check, lien search, and hour-meter sanity check fall entirely on you.
What each channel costs and protects
Auction purchases carry buyer's fees on top of the hammer price, and sales are usually final, so a missed undercarriage issue is your problem. Marketplace listings priced at retail leave room to negotiate, and you deal directly with a dealer who may offer transport or a short warranty. Classifieds cost nothing but offer no protection beyond what you check in person.
How to compare listings fast
Filter by hours, model year, and distance, then sort on photos of the undercarriage and hour meter. Dealers listing on BigEquipCo can put hours, specs, and photos in one place so buyers compare without digging through every post.
What paperwork and warranty checks protect a used skid steer buyer?
PIN and serial verification
Bobcat machines carry a PIN plate on the upper right rear of the machine, usually near the engine compartment. Match that number against the title or bill of sale before money moves. If the plate is missing, repainted over, or the stamped digits look reworked, walk away. A mismatched PIN is the fastest sign of a stolen or rebadged unit.
Service records and lien checks
Ask for filter-change dates, hydraulic and final-drive service intervals, and any undercarriage or drive-motor work. A dealer who can show hours logged against service dates is worth more than one who can only show hours on the meter. Run a lien search in the seller's state; a UCC filing you miss can cost you the machine.
Warranty and as-is terms
Most used units sell as-is, so whatever the seller promises needs to be written into the invoice. Cross-check asking prices on Machinery Trader listings so you know whether the price already reflects a warranty or you are paying retail for an as-is machine. If a dealer offers a 30-day powertrain warranty, get the covered components named in writing.
How should dealers price and list a used Bobcat skid steer to move it fast?
Pricing to rotate inventory
Price against what's already sitting on MachineryTrader and EquipmentTrader in your region, not against what you paid. If a unit needs to clear in 30 days, list at or slightly under the lowest comparable with similar hours and undercarriage condition. A price drop every two weeks beats a stale listing at your target number. For trade-ins you'd otherwise wholesale, free channels first: Craigslist and Facebook Marketplace cost nothing and stay local.
Listing details buyers actually check
Hours, year, hours again, then photos. Lead with a full shot of the machine, then close-ups of the undercarriage, bucket edges, quick-attach, cab, and hour meter. State known faults plainly; buyers on the forums reward it. Include hours on every photo caption if the platform allows. On BigEquipCo, a featured listing with a complete spec sheet is what separates you from the 20-31 active listings your regional competitors run.
FAQ
What is high hours for a used Bobcat skid steer?
Above roughly 5,000 hours, price mostly reflects what remains in the undercarriage and hydraulics rather than the machine itself. A 4,500-hour unit with a worn undercarriage can be worth less than a lower-hour, older machine. Judge hours against wear on the pedals, seat, joystick boots, and bucket edge; a low meter with heavy wear means walk away.
Are Bobcat skid steer parts still available for older models?
Yes, and this is one of Bobcat's strongest selling points on the used market. Skid steers, couplers, and buckets turn up at salvage yards and dealer counters nearly everywhere, which matters when a buyer calls about a down machine. Bushings and pivot pins are cheap consumables; even 1990s 700/800-series machines remain supportable through the parts network.
Is a used Bobcat skid steer with tracks better than tires?
Neither is universally better; it depends on the ground and the budget. Tracks spread weight and handle soft or finished surfaces, but replacement runs into four figures, so price worn undercarriage before you bid. Tires cost less to maintain and suit hard-packed or paved sites, though uneven tread wear can point to a bent axle or bad bearings.
How much does it cost to ship a used skid steer across state lines?
There is no single number; cost depends on distance, trailer type, and whether the unit is operable, and it scales with fuel and carrier rates. A full-size skid steer plus trailer can also push past common pickup tow ratings, so many buyers use a hauler. Get quotes from carriers before you commit, and factor shipping into your price ceiling.
Can I finance a used Bobcat skid steer from a private seller?
Financing a private-party purchase is harder than buying from a dealer. Most equipment lenders and banks prefer dealer transactions with clean titles and documented PINs, and private sales usually close as-is with no warranty terms. Expect a lien search in the seller's state, a verified PIN plate matching the title, and possibly a personal or credit-union loan instead.
